Digital Monitoring Products Canadain XR500 Instalační příručka stáhnout pdf (Strana 14)

Digital Monitoring Products XR500 Series Canadian Installation Guide

InstallatIon

4.3 Connecting LX-Bus and Keypad Bus Devices

Several factors determine the DMP LX-Bus™ and keypad bus performance characteristics: the wire length and gauge

used,thenumberofdevicesconnected,andthevoltageateachdevice.WhenplanninganLX-Bus™andkeypadbus

installation, keep in mind the following information:

1. DMP recommends using 18 or 22-gauge unshielded wire for all keypad and LX-Bus circuits. Do not use

twisted pair or shielded wire for LX-Bus and keypad bus data circuits.

2. On keypad bus circuits, to maintain auxiliary power integrity when using 22-gauge wire do not exceed 500

feet.Whenusing18-gaugewiredonotexceed1,000feet.Toincreasethewirelengthortoadddevices,

install an additional power supply that is listed for Fire Protective Signaling, power limited, and regulated

(12 Vdc nominal) with battery backup.

Note:Eachpanelallowsaspecicnumberofsupervisedkeypads.Addadditionalkeypadsintheunsupervised

mode.Refertothepanelinstallationguideforthespecicnumberofsupervisedkeypadsallowed.

3. Maximum distance for any one bus circuit (length of wire) is 2,500 feet regardless of the wire gauge. This

distance can be in the form of one long wire run or multiple branches with all wiring totaling no more than

2,500 feet. As wire distance from the panel increases, DC voltage on the wire decreases. Maximum number

ofLX-Busdevicesontherst2,500footcircuitis40devices.

4.Maximumvoltagedropbetweenthepanel(orauxiliarypowersupply)andanydeviceis2.0Vdc.Ifthe

voltage at any device is less than the required level, add an auxiliary power supply at the end of the circuit.

Whenvoltageistoolow,thedevicescannotoperateproperly.

ForadditionalinformationrefertotheLX-Bus/KeypadBusWiringApplicationNote(LT-2031).

Expansion Interface Cards (Models 481, 462N, 462P, and 464-263H)

TheLX-Busprovidedonthesecardsrequiresonlya4-wirecablebetweenthecardandanydevicesconnectedtothe

bus. You can connect devices (zone or output expansion modules) together on the same cable or provide separate

runs back to the card. Each LX-Bus provides up to 100 zones or outputs.

4.4 Wireless Keypad Association

EnableWirelessKeypadAssociationoperationonboththekeypadandpanel.

To enable association operation in the keypad, access the Installer Options Menu (3577

(INST)) and select RF Survey). The keypad logo LEDs turn on Red until association is

successful.

To enable association operation in the XR500 panel, reset panel 3 times within 12

seconds. Allow the keypad bus Transmit/Receive LEDs to turn back on between each

reset.

For 60 seconds the panel listens for wireless keypads that are in the Installer Options

Menu (3577 CMD) and have not been programmed, or associated into another panel.

Thosekeypadsareassignedtotherstopendevicepositionautomaticallybasedupon

theorderinwhichtheyaredetected.ThekeypadlogoturnsGreentoindicateithasbeenassociatedwiththepanel.

Primary Power Supply

5.1 AC Terminals 1 and 2

Connectthetransformerwirestoterminals1and2onthepanel.Usenomorethan70ft.of16gaugeor40ft.of18

gauge wire between the transformer and the XR500 Series.

Always ground the panel before applying power to any devices: The XR500 Series must be properly

grounded before connecting any devices or applying power to the panel. Proper grounding protects

against Electrostatic Discharge (ESD) that can damage system components. See the Earth ground section.

5.2 Transformer Types

Use Model 327-CAN (16.5 Vac 50 VA) plug-in or Model FTA7516 from ATC Frost.

The transformer must be connected to an unswitched 120 Vac 60 Hz electrical outlet with at least .87A of

available current. Never share the transformer output with any other equipment.

5.3 J12 3-Pin Header for Transformer Types

Place the jumper on the left two pins for a Maximum 2 Amp (Bell=1 Amp; Aux=1 Amp) when using the Model 327-CAN

plug-in transformer (default).

Use an ATC Frost FTA7516 transformer and place the jumper on the right two pins for a Maximum, 3 Amps (Bell=1.5

Amp; Aux=1.5 Amp).

Secondary Power Supply

Programming

XMIT

RCV

Figure 5: Keypad Bus LEDs

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 39 40

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products Canadain XR500 Instalační příručka Strana 14

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products Canadain XR500