Digital Monitoring Products XR20 Instalační příručka stáhnout pdf (Strana 21)

XRSuper6/XR20/XR40 Installation Guide Digital Monitoring Products

ComplIanCe

ANSI/UL 1023 Specications

Household Burglar-Alarm System Units

16.1 Bell Cutoff

The bell cutoff time cannot be less than ve minutes. See the XRSuper6/XR20/XR40 Programming Guide

(LT-0305).

16.2 Entry Delay

The maximum entry delay used must not be more than 45 seconds. See the XRSuper6/XR20/XR40

Programming Guide (LT-0305).

16.3 Exit Delay

The maximum exit delay used must not be more than 60 seconds. See the Programming Guide (LT-0305).

16.4 Zone Expansion on 4-Wire Bus

When expansion zones are used, the keypad and zone expander 4-wire bus must be limited to three feet

in length unless an external communication fail indicator is added. A 12 VDC relay may be wired as a

communication fail indicator. To install, connect the negative side of the indicator to one of the panel’s

annunciator outputs and the positive side to the smoke power (terminal 11 of the panel). See the XRSuper6/

XR20/XR40 Programming Guide (LT-0305).

In addition to the wiring described above, a 24-hour zone must be programmed to activate the appropriate

annunciator output.

16.5 Wireless External Contact

When used, the External Contact of 1101, 1102, or 1103 must be programmed Normally Closed. See the

XRSuper6, XR20, XR40 Programming Guide (LT-0305).

16.6 Wireless Supervision Time

The Zone Information Supervision Time cannot be set to 0 (zero). See the XRSuper6, XR20, XR40

Programming Guide (LT-0305).

16.7 Wireless Audible Annunciation

The Wireless Audible option must be selected as DAY for residential applications.

ANSI/UL 1610 and ANSI/UL 1076 Specications

Central-Station and Proprietary Burglar-Alarm Units

17.1 Opening/Closing Reports

The Opening/Closing Reports option must be programmed as YES. See the Programming Guide (LT-0305).

17.2 Automatic Bell Test

This option must be programmed as YES. See the XRSuper6/XR20/XR40 Programming Guide (LT-0305).

17.3 Proprietary Dialer

The Model XRSuper6/XR20/XR40 provide proprietary service when congured as a digital dialer.

17.4 Standard Line Network Security

Standard Line Security is provided when congured as a NET system using an XRSuper6, XR20, or XR40 panel

with an iCOMSL™ Network Alarm Router. The NET Check-in time must be set from 01 to 06 minutes. When a

dialer is required for 06 minute check-in time, an attack resistant enclosure (DMP Model 350A) is required.

When the check-in time is set to a number less than 200 seconds (1, 2, or 3 minutes), an attack resistant

enclosure is not required. See the Communication section of the XRSuper6, XR20, XR40 Programming Guide

(LT-0305).

17.5 Wireless Arming Mode

The System Options Mode for arming must be programmed as Area or All/Perimeter (A/P). See the

XRSuper6/XR20/XR40 Programming Guide (LT-0305).

17.6 Wireless Tamper

The Zone Information Disarmed Open Message to Transmit must be programmed Trouble (T). See the

XRSuper6/XR20/XR40 Programming Guide (LT-0305).

17.7 Wireless External Contact

When used, the External Contact of 1101, 1102, or 1103 must be programmed Normally Closed. See the

XRSuper6/XR20/XR40 Programming Guide (LT-0305).

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 30 31

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products XR20 Instalační příručka Strana 21

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products XR20