Digital Monitoring Products XR2500F Manuál s instrukcemi stáhnout pdf (Strana 56)

XR500 Series Programming Guide Digital Monitoring Products

zone informaTion

19.9

NEXT ZN? NO YES

Next Zone

Select YES to terminate zone programming. The display returns to Zone Number,

allowingyoutoenteranewzonenumber.SelectNOtomakealterationstothe

AlarmActionforazone.AlarmActionisdenedbeginningwithsection16.12.

Toprogramzonesforwirelessoperation,selectNOattheNEXTZONE-NOYES

option.TheWIRELESSNOYESoptiondisplays.Ifthezoneyouareprogramming

isintendedforwirelessdevices,selectYES.SelectNOtocontinueprogramming

non-wirelesszonesinthe500to999range.

• Zones400to449canbeprogrammedfor1100SeriesKeyFobs.

• Zones500to699canbeprogrammedforFASeriesWireless.

• Zones500through999canbeprogrammedforDMP1100SeriesWireless.

DMP Wireless

For a DMP 1100X Wireless Receiver set the House Code from 1 to 50. See House Code programming in

SystemOptions.Zones500through999canbeprogrammedasWirelesszones.SettheXR500Seriespanel

J23jumpertoXtoenableon-boardDMPWirelessoperation.BrieyresetthepanelusingtheJ16jumper

toactivateWirelessoperation.RefertotheXR500SeriesInstallationGuide(LT-0681).

For an 1100 Series Key Fob see section 19.11.

For an FA Series Remote Wireless Receiver see section 19.12.

NOTE: AllwirelessprogrammingisstoredintheXR500Seriespanel.The1100XWirelessReceiverobtains

the necessary programming information from the panel each time the receiver powers up, when the

programmerSTOProutineisselectedorthepanelisreset.Thereceivermemoryrefreshtakesupto10

secondstocompletedependingonthenumberofwirelesszonesprogrammedandtheRedLEDremainson

during this time. Normal receiver operation is inhibited during the memory refresh period.

19.10 Wireless

Select YES to program this zone as a DMP wireless zone. You must program

the wireless House Code prior to adding DMP wireless zones to the system. See

HouseCodeprogramminginSystemOptions.DefaultisNO.

19.10.1

TRANSMITTER

SERIAL#: XXXXXXXX

Serial Number Entry

Entertheeight-digitserialnumberfoundonthewirelessdevice.

ALREADY IN USE

ZONE NUMBER: XXX

This message displays when the serial number is already programmed for

another zone. The programmed zone number displays.

19.10.2

TRANSMITTER

CONTACT:XXXXXXXX

Contact

Thisoptiondisplaysiftheserialnumberenteredisforan1101or1103Universal

Transmitteror1114WirelessFour-ZoneExpander.Pressanytoprowkeyto

select the contact.

TRANSMTR CONTACT

INT EXT

Thisoptiondisplayswhenprogrammingan1101or1103Transmitter.SelectINT

to use the internal reed switch contacts. Select EXT to connect an external

devicetothe1101or1103terminalblock.DefaultisINTERNAL.

ByallowingbothoftheModel1101or1103transmittercontacts(INTand

EXT)tobeusedatthesametime,twozonesmaybeprogrammedfrom

onetransmitter.Whenusingbothcontacts,youmustuseconsecutivezone

numbers.Zones531and532orzones890and891areacceptablezone

assignments.

Forexample,programtransmitterserialnumber01345678asZone521with

an INT contact type and Zone 522 with an EXT contact type. The same serial

number is used for both zones.

Note:Whenusingthe1103UniversalTransmitterinaULlistedCommercial

Burglary installation, the external contact cannot be used.

ZONE INFORMATION

WIRELESS? NO YES

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 ... 79 80

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products XR2500F Manuál s instrukcemi Strana 56

Komentáře k této Příručce

Související produkty a manuály pro Detektory kouře Digital Monitoring Products XR2500F