Digital Monitoring Products XR20 Instalační příručka stáhnout pdf (Strana 16)

Installation

XRSuper6/XR20/XR40 Installation Guide

Digital Monitoring Products www.dmpnet.com 2500 N. Partnership Boulevard Springfield, MO 65803

Annunciator Outputs

12.1 Description

The four annunciator outputs can be programmed to indicate the activity of the panel's zones or conditions

occurring on the system. Annunciator outputs do not provide a voltage but instead switch to ground voltage

from another source. The outputs can respond to any of the conditions listed below:

1) Activation by zone condition: Steady, Pulse, Momentary, or Follower 7) Exit and Entry timers

2) Manually from the Security Command keypad 8) System Ready

3) Communication failure 9) Ground start activation

4) Armed area annunciation 10) Cellular Backup

5) Fire Alarm or Fire Trouble 11) Late to Close

6) Ambush alarm

12.2 Harness wiring

The open collector outputs are accessible by installing the DMP 300 Harness on the 4-pin header labeled J11.

The output locations are shown below. For UL applications, devices connected to the outputs must be located

within the same room as the panel.

Output Color Wire Output Color Wire

1 Red 1 3 Green 3

2 Yellow 2 4 Black 4

12.3 Model 860 Relay Module

You may connect a Model 860 Relay Module to the panel to provide relays for the annunciator outputs. These

relays can be used for electrical isolation between the alarm panel and other systems or for switching voltage to

control various functions. The module includes one relay and provides three additional sockets for expansion of

up to four relays. A 4-wire harness is also provided that connects the Model 860 to the DMP panel.

The 860 mounts inside the panel enclosure using the 3-hole mounting configuration. Plastic standoffs are provided

with the module for ease of installation. Power is supplied to the relay coils from the panel's keypad bus.

Relay Contact Rating: 2 Amps at 30 VDC

Telephone RJ Connector

13.1 Description

Connect the panel to the public telephone network by installing a DMP 356 RJ Cable between the panel's J4

connector and the RJ31X or RJ38X phone jack.

Phone Cable Monitor

A two pin header labeled RJ SUP (J7) is provided to allow monitoring of the telephone cable connected between

the panel and a RJ38X jack (pins 2 and 7 jumpered). Attach a DMP Model 306 Harness between J7 and any

available zone. The pins of J7 are connected via the telephone cable to 2 and 7 of the RJ38X jack. The RJ38X

jack provides a jumper between pins 2 and 7 which completes the circuit.

When the zone is programmed for a Supervisory type (SV) and the telephone cable is removed, the keypad will

display the zone in trouble and produce a steady tone.

13.2 FCC registration

The panel complies with FCC part 68 and is registered with the FCC.

Registration number: CCKUSA - 18660 - AL - R

Ringer Equivalence: 1.1B

13.3 Notification

Registered terminal equipment must not be repaired by the user. In case of trouble, the device must be

immediately unplugged from the telephone jack. The factory warranty provides for repairs. Registered terminal

equipment may not be used on party lines or in connection with coin telephones. Notification must be given to

the telephone company with the following information:

a. The particular line(s) the service is connected to

b. The FCC registration number

c. The ringer equivalence

d. The make, model, and serial number of the device

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products XR20 Instalační příručka Strana 16

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products XR20