Digital Monitoring Products XR20 Instalační příručka stáhnout pdf (Strana 26)

Digital Monitoring Products XRSuper6/XR20/XR40 Programming Guide

SySTem oPTionS

6.15

HOUSE CODE: 0

House Code

When using a DMP wireless system, enter a house code between 1 and 50 for the

wireless system to use. The DMP wireless receiver automatically programs the house

code into the wireless transmitters when the unique transmitter serial number is

programmed into the panel. See Wireless programming in Zone Information. Default

is 0 (zero) indicating the DMP wireless system is not being used.

The house code identies the panel, receiver, and transmitters to each other. When

operating, the receiver listens for transmissions that have the programmed house

code and transmitter serial number.

Note: The exibility of DMP two-way wireless operation allows an existing house code

to be changed in the panel at any time. The transmitter may take up to two minutes

to learn the new house code and continue operation.

Note: When any wireless zone programming is changed in the panel, wireless

receiver zone programming is updated by the panel. At that point, all wireless zones

display as normal for up to 1 minute, regardless of the actual state of the zone.

6.16

DET JAMNG NO YES

Detect Wireless Jamming

This option displays when the House Code entered is for a DMP 1100D Series Wireless

system. When enabled and the receiver detects jamming, a trouble or alarm

message is sent to the receiver and displays in the Status List. Select YES to enable

jamming messages to display in the Status List. Select NO to disable jamming

messages. Default is NO.

6.17 Wireless Audible Annunciation

This option displays when the House Code entered is for a DMP 1100 Series Wireless

system (1-50). Press any top row key to select the keypad buzzer annunciation

method for wireless low battery and missing messages. Select ANY to enable

annunciation anytime. Select DAY to enable annunciation except during sleeping

hours (9 PM to 9 AM). Select MIN (minimum) to annunciate only Fire and Fire Verify

zones during daytime hours (9 AM to 9 PM). Default is DAY.

6.18

KPD PANCS NO YES

Enable Keypad Panic Keys

This option allows the two-button panic key operation selected at a keypad to send

the Panic, Emergency, or Fire message to the central station receiver. Select YES to

enable the two-button panic operation. To disable the two-button panic operation,

select NO. Default is YES.

6.19

SIA CP-01 NO YES

SIA CP-01

Select YES to allow the panel to operate according to ANSI/SIA CP-01 standards for

the following operations. Select NO to enable standard DMP operation. Default is

YES. When YES is selected:

Power Up and Stop Routine

— the 60 second zone startup delay is turned on.

Keypress Alarm Silence

— during an alarm, the keypad alarm and bell output turn off when the rst key is

pressed at a keypad.

Entry Delay

— entering the rst digit of a code at the keypad stops the prewarn tone.

 Exit Delay

— the keypad displays the Exit Delay time countdown and annunciates a tone at

8 second intervals until the last 10 seconds when annunciation is at 3 second

intervals.

Exit Error Operation

When the exit zone is faulted (door still open) at the end of the exit delay:

— the bell sounds for the length of time set in Bell Cutoff programming

— the Entry Delay operation starts, requiring code entry to disarm

— if not disarmed, a zone alarm and an Exit Error are sent to the receiver.

Automatic Disarming Operation

— For All/Perimeter or Home/Sleep/Away systems the Interior automatically

disarms if a Perimeter exit zone is not tripped during the Exit Delay time when

arming All or Away at the keypad.

ANY DAY MIN

WLS AUDIBLE: DAY

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 51 52

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products XR20 Instalační příručka Strana 26

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products XR20