Digital Monitoring Products XR550 Uživatelská příručka stáhnout pdf (Strana 17)

10 XR150/XR350/XR550 User’s Guide Introduction

ALARM NOT SENT

The alarm signal was aborted and was not sent to the central

station because a user code was entered to disarm the system

before the alarm signal was sent to the central station. Also, your

system may be pre-programmed at installation to send an Abort

signal to the Central Station that an alarm occurred but was

not sent because the user entered a code before the delay time

expired. Refer to the Introduction section of this guide.

ALARM CANCELLED

An Alarm signal just sent to the central station was cancelled

because a user code was entered to disarm the system after the

alarm was sent. Also, an Alarm Cancel signal is sent to the Central

Station.

ALARM VERIFIED

$YDOLGEXUJODUDODUPKDVRFFXUUHGDQGKDVEHHQPDQXDOO\YHULÀHG

by the user. The alarm system also transmits a VERIFY message to

the Central Station.

ENTER CODE OR PRESENT CARD

The system requires you to enter your user code or present your

user card/proximity credential to a keypad or card reader. User

FRGHVRUUHDGVFDQEHUHTXLUHGIRUWXUQLQJ\RXUV\VWHPRQDUPLQJ

WXUQLQJ\RXUV\VWHPRIIGLVDUPLQJDQGPDQ\RWKHUIXQFWLRQV

As you enter your user code, the keypad display shows an asterisk

 LQ SODFH RIHDFK GLJLW SUHVVHG7KLV NHHSV RWKHUV IURP VHHLQJ

your user code on the display as it is entered.

TRY AGAIN OR INVALID CODE/CARD/PIN

7KHXVHUFRGHFDUGUHDGRU3,1\RXKDYHXVHGLVQRWUHFRJQL]HG

by the system. Check the user code or PIN or present the card to

the reader again.

INVALID PROFILE

$OO XVHU FRGHV KDYH D SURÀOH WKDW DOORZ WKH XVHU WR RQO\ DFFHVV

certain functions. When users attempt functions outside their

DXWKRULW\WKH,19$/,'352),/(PHVVDJHGLVSOD\V

INVALID AREA

A user has attempted a door access for an area they are not

assigned.

INVALID TIME

$XVHU FRGHDVVLJQHG WR DVSHFLÀF VFKHGXOHLV HQWHUHGRXWVLGH RI

the valid schedule. See Schedules and User Codes.

ARMED AREA

A user has attempted a door access to an armed area to which they

do not have arming and disarming authority.

FAILED TO EXIT (ANTI-PASSBACK)

$QWLSDVVEDFNUHTXLUHVXVHUVWRSURSHUO\H[LWHJUHVVDQDUHDWKH\

have previously accessed. If they fail to exit through the proper

card reader location, they are not granted access on their next

attempt. A Failed to Exit message appears when a user assigned

the anti-passback option attempts to re-enter an area which

they did not exit properly. The user must exit the area through

the proper door. If not possible, your system administrator should

select the Forgive option in the User Codes menu option.

SYSTEM TROUBLE or SERVICE REQUIRED

There is a problem with one or more of the components in your

system. Contact our service department as soon as possible.

SYSTEM BUSY

The system is performing another task of a higher priority. This

usually only takes a few moments.

TEST IN PROGRESS

The system is currently being tested by an installation or service

technician.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 83 84

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products XR550 Uživatelská příručka Strana 17

Komentáře k této Příručce