Digital Monitoring Products XR550 Uživatelská příručka stáhnout pdf (Strana 19)

12 XR150/XR350/XR550 User’s Guide Introduction

,IWKHDODUPLVIURPDKRXU]RQHRUDV\VWHPPRQLWRULWUHPDLQV

in the Sta tus List until it re stores. If one or more armed burglary

]RQHV WULS DW WKH VDPH WLPH WKH ODVW RQH WR WULS UHPDLQV LQ WKH

Status List. This is to ensure that if a burglary has occurred the last

]RQHWULSSHGUHPDLQVGLVSOD\HGHYHQLILWKDVEHHQUHVWRUHG

Armed Status

Armed Status is the keypad display of the current armed condition

of areas within your security system.

If your system is set up as an Area system with areas one to eight,

WKHGLVSOD\VKRZV:KHQ\RXDUPDUHDVDQG

7 the keypad displays: 1 3 5 7.

If your Area system is setup with nine or higher areas and the system

LV DUPHG WKH GLVSOD\ UHDGV $// 6<67(0 21 RU 6<67(0 21 5HIHU WR

Checking Armed Areas for information about checking the armed areas.

If your system is set up as a Home/Sleep/Away or All/Perimeter

system, one of the following displays indicate the current Armed

Status:

7KHNH\SDGGLVSOD\V :KHQ

HOME SYSTEM ON The perimeter is armed in a Home/

Sleep/Away system.

PERIMETER ON The perimeter is armed in an All/

Perimeter system.

ALL SYSTEM ON All areas are armed.

SLEEP SYSTEM ON The perimeter and interior are armed

but the bedroom area is disarmed.

If your system is set up as a Home/Sleep/Away with Guest system,

the arming status of the main system is the same as a standard

Home/Sleep/Away system. The current arming status of the Guest

systems displays as follows:

Instant Zone

Interior protection devices and perimeter devices, such as exterior

ZLQGRZV SDVVLYH LQIUDUHG GHWHFWRUV 3,5 DQG QRQ HQWU\ GRRUV

DUHW\SLFDOO\QRWSURJUDPPHGZLWKGHOD\WLPHV,IWKHVH]RQHVDUH

tripped while the system is armed, an alarm instantly occurs.

24-hour Zone

$KRXU]RQHLVQRWWXUQHGRQRURIIE\DUPLQJRUGLVDUPLQJ\RXU

V\VWHP 6RPH H[DPSOHV RI KRXU ]RQHV DUH ÀUH ]RQHV SDQLF

]RQHVDQGWHPSHUDWXUHFRQWURO]RQHV

Entry or Exit zone

Almost all systems have one or more doors through which you can

access the premises. These doors are programmed with a delay

time to allow you to enter or exit without setting off the alarm.

:KHQ \RX DUP WKH V\VWHP DFWLYLW\ RQ WKLV ]RQH LV LJQRUHG XQWLO

WKHH[LW GHOD\WLPH H[SLUHV 2QFH WKDW WLPH KDV H[SLUHGDQGWKH

system is fully armed, opening the door causes the panel to start

the entry delay time. During the entry delay time, you must enter

a valid user code to disarm the system or an alarm occurs.

Status

Status is a feature that automatically displays the armed or dis-

armed status of your system on the keypads. Alarm or trouble

FRQGLWLRQV RQ D ]RQH RU D V\VWHP PRQLWRU VXFK DV$& RU EDWWHU\

trouble can also display. There are two types of status information

available: Armed Status and Status List.

Status List

The keypad Status List displays any alarm or trouble condition on

D]RQHDQGDQ\WURXEOHFRQGLWLRQRQDQLQWHUQDOV\VWHPPRQLWRU

The system monitors include the AC power, battery power, panel

box tamper, printer, and phone lines. If more than one alarm or

trouble condition occurs at the same time, the keypad sequences

this information on its display.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 83 84

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products XR550 Uživatelská příručka Strana 19

Komentáře k této Příručce