Digital Monitoring Products Canadian XR100 Instalační příručka stáhnout pdf (Strana 25)

Digital Monitoring Products XR100 Series Installation Guide

INSTALLATION

XR100 Series Installation Guide Digital Monitoring Products

INSTALLATION

J23 6-Pin Header

14.1 Description

The XR100 Series Command Processor™ panel supports Direct Programming, LX-Bus, and, DMP Wireless operation.

These operations cannot function at the same time. Install a jumper on one pair of J23 headers to indicate how

the panel is programmed to operate. Refer to the table below when installing a jumper on J23. When a jumper

is installed or moved on the 6-pin header, briey reset the panel using the J16 jumper to activate the selected

operation.

Note: The Direct Programming, LX-Bus operation, and DMP Wireless operations cannot be used at the same time.

J23 6-pin Header

Letter Operation

R Direct Programming

L LX-Bus

X DMP Wireless

J22 LX-Bus Expansion Connector

15.1 Description

The XR100 Series Command Processor™ Panel supports one LX-Bus circuit that provides 100 expansion zones, DMP

Wireless that provides 100 wireless zones, or direct connect programming. Enable J22 LX-Bus Header to use the 100

expansion or wireless zones.

15.2 J22 LX-Bus Header

Note: The LX-Bus, DMP Wireless, and Direct Programming operations cannot be used at the same time.

For each connection, respect wire colors when connecting devices and use all four wires. After placing the jumper

on the J23 6-Pin header to enable the required operation, briey reset the panel using the J16 jumper to activate

operation.

Wireless Bus Operation: Place a jumper on the two pins next to the letter “X” on the J23 6-Pin header. When using

J22 as a wireless bus, connect a DMP Model 300 4-wire Harness to the J22 4-pin header labeled LX. Connect the

other end to the J3 header on the 1100X Wireless Receiver. This provides up to 100 wireless zones numbered 500 to

599. Refer to the 1100X Wireless Receiver Install Guide (LT-0708).

LX-Bus Operation: Place a jumper on the two pins next to the letter “L” on the J23 6-pin header. When using J22

as an LX-Bus, connect a DMP Model 300 4-wire Harness to the J22 6-pin header labeled LX. This provides 100 LX-Bus

zones numbered 500-599.

Note: Do NOT use shielded wire when using the LX-Bus.

Direct Programming Operation: Place a jumper on the two pins next to the letter “R” on the J23 6-Pin header.

When using J22 as a direct programming port, connect a the 4-wire connector from DMP Model 399 Harness to the

J22 4-pin header labeled LX. Connect the Model 399 DB-9 connector onto an RS-232 port on a Laptop computer.

This allows direct panel programming from the attached computer.

15.3 LX-Bus LEDs

The two LEDs, located near the bottom-right corner of J21 indicate data transmission and receipt. The top LED

ashes green to indicate the panel is transmitting LX-Bus data. The bottom LED ashes yellow to indicate the panel

is receiving LX-Bus data.

15.4 OVC LED

The Overcurrent LED (OVC) lights Red when the devices connected to the Keypad Bus and LX-Bus(es) draw more

current than the panel is rated for. The OVC is located above Outputs 1 and 2 on the panel and turns a steady Red

when lit. When the OVC LED lights Red, the LX-Bus(es) and Keypad bus shut down.

Figure 6: J23 6-pin Header

LEDs

Xmit

Receiv

J22

Overcurrent

LED

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 45 46

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products Canadian XR100 Instalační příručka Strana 25

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products Canadian XR100