Digital Monitoring Products Graphic Touchscreen Uživatelská příručka stáhnout pdf (Strana 25)

18 XR150/XR350/XR550 User’s Guide Arming and Disarming

All/Perimeter System Arming

Area Assignment: Your security system is divided into two

separate areas. Motion detectors, inside doors, and other interior

protection devices are assigned to the Interior area while windows

and exterior doors are assigned to the Perimeter area.

Perimeter or All: When arming an All/Perimeter system, the

keypad displays PERIM ALL. If you select ALL, you are arming

both the Perimeter and the Interior areas of the system. You will

want to arm both of these areas when leaving the premises with

nobody left inside. Selecting PERIM arms only the perimeter of the

system. Perimeter arming is when you’re staying inside but want

the comfort of knowing the exterior doors and windows are armed.

Perimeter arming allows you to move freely about inside without

setting off any interior alarms.

Instant: During the exit delay time, you can cancel the exit and

entrydelaysandcauseallzonestobeinstantzones.Justpressthe

far right Select key under INSTNT while the exit delay is displayed.

Thisimmediatelyarmstheexitzones.However,noentrydelayis

provided and an alarm will occur should an entry door be opened.

System Ready/System Not Ready

When all zones in the system are in a normal condition and can

be armed without bypassing, the keypad displays SYSTEM READY.

Ifthereareoneormorezonesthatarenotinanormalcondition,

the keypad displays SYSTEM NOT READY. Pressing any Select key

duringthisdisplayshowsthezonenumberandnameallowingyou

to investigate the problem.

All/Perimeter Shortcut Key Arming

Arm Perimeter —Press6for2seconds.

Arm All — Press 1 for 2 seconds.

Arming an All/Perimeter System

Enter your 4-digit user code. The keypad displays PERIM ALL.

2. Select PERIM to arm the Perimeter area only.

3. Select ALL to arm both the Perimeter and Interior areas.

4. Thekeypaddisplayszonesthathavebeenbypassedpriorto

armingandzonesthatarenowinafaultedcondition.

5. Atthispointyoucanforcearmorbypassanyfaultedzones.

Azonethatisforcearmedisrestoredintothesystemifit

laterreturnstonormal.Abypassedzoneremainsbypassed

until the system is disarmed. See steps 5a through 5d.

5a. If a problem exists on any zones, the zone name and

problemdisplayfollowedby:OKAYBYPASSSTOP.

5b. SelectOKAYtoforcearmthezone(s)beforearming.

5c. SelectBYPASStobypassthezone(s)beforearming.

5d. SelectSTOPtostopthesystemfromarming.Correctthe

zoneproblem(s)andreturntostep1.

6. ThekeypaddisplaysPERIMETERONifonlytheperimeteris

beingarmedandALLSYSTEMONifboththeperimeterand

interior are being armed.

7. If arming Perimiter, the keypad displays EXIT:  ## INSTNT

and begins to count down the number of seconds remaining

foryoutoexit.Whenthedelayexpires,allzonesarearmed.

8. You can select INSTNT while EXIT:  ## INSTNT displays to

immediately arm all zones and make them instant. The

keypad displays INSTANT. When you select INSTANT, any

entry/exit zone that trips immediately activates an alarm

and the exit delay countdown immediately stops.

9. When the system is fully armed, the keypad displays

PERIMETERONforperimeterarmingandALLSYSTEMONfor

perimeter and interior arming.

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 83 84

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products Graphic Touchscreen Uživatelská příručka Strana 25

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products Graphic Touchscreen