Digital Monitoring Products XR20 Instalační příručka stáhnout pdf (Strana 18)

XRSuper6/XR20/XR40 Programming Guide

Digital Monitoring Products www.dmpnet.com 2500 N. Partnership Boulevard Springfield, MO 65803

5.1 SYSTEM REPORTS

This function allows you to select the reports the XRSuper6/XR20/XR40 send to the

receiver.

5.2 OPENING/CLOSING REPORTS

This option allows the selection of Opening/Closing Reports and the number of

reports sent to the receiver.

NO - Opening/Closing Reports are not sent by the panel.

YES - The panel will send Opening/Closing Reports for each programmed area.

LTD - The panel sends only one opening and one closing report. When LTD is

selected and all areas become armed, the panel sends a General Closing Report.

Then after the first disarming, the panel sends a General Opening Report.

Therefore, when LTD is selected the panel will only send a report after all areas are

armed and then at the first disarm of an area. All openings and closings will be

logged in the event buffer. This option is only available when the communication

type is CID or M2E. Refer to the Communication Type section.

ALM - The panel sends only one opening report if an alarm has occurred during the

last armed cycle. The panel will send a General Opening Report. The panel does not

send closing reports when ALM is selected. All other openings and closings will be

logged in the event buffer. This option is only available when the communication

type is CID or M2E. Refer to the Communication Type section.

5.3 ABORT REPORT

YES allows the panel to send an alarm abort report to the receiver any time an area

is disarmed after an alarm report has been sent and the Bell Cutoff Time has not

expired. See the Bell Cutoff section. The area must be disarmed and no alarmed

zones can still be armed. YES also allows a Bell Silenced Report to be sent if the

alarm bell is silenced with a valid user code during an alarm, if the communication

type is set to DD. When the system is disarmed during an alarm, only Abort and

Opening Reports are sent. Abort reports are also sent when the system is disarmed

during Transmit Delay and the Bell Cutoff Timer is active.

Note: Abort reports will not be sent for Fire zones, Fire Verify, or Supervisory type

zones.

5.4 ZONE RESTORAL REPORTS

This option allows you to specify whether the panel sends zone restoral reports and

also when they will be sent.

NO - Restoral reports are not sent by the panel.

YES - The panel always sends zone restoral reports at the time the zone restores

from an alarm or trouble condition.

DISARM - The panel sends zone restoral reports when a zone that has restored from

an alarm or trouble is disarmed. Twenty-four hour zones send restorals immediately.

5.5 BYPASS REPORTS

YES allows the panel to send all zone bypass, reset, and force arm reports to the

receiver. The bypass report includes the zone number, zone name, and the user

number of the individual bypassing the zone.

5.6 CODE CHANGE REPORTS

YES allows the panel to send all code additions, changes, and deletions to the

receiver. The code change report includes the user number added or deleted and

the user number of the individual making the change.

5.7 AMBUSH

YES allows an ambush report to be sent any time user code number one is entered at

a keypad. Selecting NO disables the ambush report and allows user code number one

to operate the same as all other codes.

RESTORAL: YES

NO YES DISARM

BYPASS YES

CODE CHG NO

AMBUSH NO

SYSTEM REPORTS

ABORT NO

OPN/CLOS NO

NO YES LTD ALM

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 37 38

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products XR20 Instalační příručka Strana 18

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products XR20