Digital Monitoring Products Canadian XR100 Instalační příručka stáhnout pdf (Strana 20)

Digital Monitoring Products XR100 Series Canadian Installation Guide

InstallatIon

Protection Zones

10.1 Terminals 13–24

Zones1to8(terminals13to24)ontheXR100Seriespanelareallgroundedburglaryzones.Forprogrammingpurposes,

thezonenumbersare1through8.Listedbelowareterminal13to24connectionfunctions.

Terminal Function Terminal Function

Zone 1 voltage sensing

Zone 5 voltage sensing

GroundforZones1and2

GroundforZones5and6

Zone 2 voltage sensing

Zone 6 voltage sensing

Zone 3 voltage sensing

Zone 7 voltage sensing

GroundforZones3and4

GroundforZones7and8

Zone4voltagesensing

Zone 8 voltage sensing

The voltage sensing terminal measures the voltage across a 1k Ohm End-of-Line resistor to ground. Use DMP Model 311 1k

Ohm resistors. Dry contact sensing devices can be used in series (normally-closed) or in parallel (normally-open) with any

of the burglary protection zones.

Each protection zone detects three conditions: Open, Normal, and Short. Listed below are voltage and resistance

parameters for each condition:

Condition Resistance on zone Voltage on positive terminal

Open over 1300 ohms over 2.0 Vdc

Normal 600 to 1300 ohms 1.2 to 2.0 Vdc

Short under 600 ohms under 1.2 Vdc

10.2 Dual EOL

TheXR100SeriesCanadianpanelsupportstheuseofdual1KEOLresistorsonpanelzonesonetoeight.

Two EOL resistors are used so a wire trouble can be indicated during the disarm period.

Whendualend-of-lineoperationischoseninpanelprogramming,normalzoneprocessingoccurs

withthefollowingexception:WhenprocessinganopenzoneandatroubleoralarmmessageisNOT

programmed to be sent for the open state, the panel checks to see if the wire is cut. If the wire is cut,

the panel automatically sends an alarm if armed or trouble is disarmed.

ZONE STATUS

Zone Wires Open Zone Wires Short Contact Normal Contact Open

Disarmed Trouble Trouble Normal Normal

Armed Alarm Alarm Normal Alarm

10.3 Zone Response Time

A condition must be present on a zone for 500 milliseconds before it is detected by the XR100 Series panel. Ensure

detection devices used on the protec tion zones are rated for use with this delay. Zones 1-10 can also be programmed for a

fast response delay of 160 milliseconds.

10.4 Keyswitch Arming Zone

A keyswitch on an Arming type zone allows selected areas to arm and disarm without having to enter a user code.

Powered Zones for 2-Wire Smoke Detectors

11.1 Terminals 25–26 and 27–28

Panel terminals 25 through 28 provide two resettable Class B, Style A, 2-wire powered zones. For programming purposes

the zone numbers are 9 and 10.

Note:Themaximumwirelengthforeitherzone9orzone10is3000feetusing18AWGor1000feetusing22AWG.The

maximumvoltageis14Vdcandmaximumcurrentis1.25mADC.Themaximumlineimpedanceis100Ohms.Themaximum

short circuit current is 56mA.

Whenusingallotherzoneexpansionmodules,useULListedModel309EOLresistors.Thecompatibilityidentierforthe

zones is A.

Note: Do not mix detectors from different manufacturers on the same zone.

Caution: Performing a Sensor Reset momentarily drops power to the devices on Zones 9 and 10. The panel

viewsthesezones(9and10)as“Open”whilethepowerisabsent.

Figure 5: Protection Zone Wiring

1K Ohm

Normally

Closed

1K Ohm

Normally Open

1K Ohm

Combination Normally Open

and Normally Closed

1K Oh

1K Ohm

Indicating Device

Zone wires

to Panel

Zones 1-8

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 35 36

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products Canadian XR100 Instalační příručka Strana 20

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products Canadian XR100