Digital Monitoring Products Canadian XR100 Instalační příručka stáhnout pdf (Strana 8)

Digital Monitoring Products XR100 Series Canadian Installation Guide

IntroductIon

2.2 Zone Expansion

Upto142additionalzonesareavailableontheXR100SeriesusingDMPLCDkeypadremotezonecapabilityandzone

expansion modules. The panel keypad data bus supports up to eight supervised device addresses with each address

supporting up to four programmable expansion zones.

Upto100zonesareavailableusingtheonboardLX-Bus,Model481,462Nand464-263H,andanycombinationofsingle,

four, eight, or 16-zone expansion modules and single-zone LX-Bus™ detectors.

Note:DonotuseshieldedwireforLX-BusorKeypadBuscircuits.

2.3 Output Expansion

In addition to the two SPDT relays and four programmable open collector outputs on the XR100 Series, you can also

connect up to 25 programmable Model 716 Output Expansion Modules. These modules can provide an additional 100

programmable SPDT relays.

The XR100 Series provides 100 Output Schedules for programming the 716 to perform a variety of annunciation and control

functions. Also assign the 716 outputs to any panel Output Options such as Fire Alarm, Communication Fail, or Phone

TroubleOutputs.Refertothe716InstallationGuide(LT-0183).

TheLX-Bus™alsosupportstheModel717GraphicAnnunciatorModule.Each717modulesupplies20switchedground

outputs that follow the state of their assigned zones.

Note:The717supportsthersteightKeypadBusaddresses.Refertothe717InstallationGuide(LT-0235)and716

InstallationGuide(LT-0183).

2.4 Central Station Communication

Program the XR100 Series panel for reporting to DMP SCS-1R or SCS-VR Receivers using digital dialer, cellular, network, or

Contact ID communication. The XR100 Series connects at the premises to a standard RJ31X or RJ38X telephone jack. Use

the DMP 893A Dual Phone Line Module when connecting the XR100 Series panel to two separate phone lines.

2.5 Caution Notes

Throughout this guide you will see caution notes containing information you need to know when installing the panel. These

cautionsareindicatedwithayieldsign.Wheneveryouseeacautionnote,makesureyoucompletelyreadandunderstand

its information. Failing to follow the caution note can cause damage to the equipment or improper operation of one or

more components in the system. See the example shown below.

Always ground the panel before applying power to any devices: The panel must be properly grounded

before connecting any devices or applying power to the panel. Proper grounding protects against Electrostatic

Discharge (ESD) that can damage system components.

2.6 Compliance Instructions

For applications that must conform to a local authorities installation standard or a National Recognized Testing Laboratory

certicatedsystem,pleaseseetheListedComplianceSpecicationssectionneartheendofthisguideforadditional

instructions.

System Components

3.1 Description

The DMP XR100 Series system is made up of an alarm panel with a built-in communicator, an enclosure, battery, one 16.5

Vac transformer, and keypads. You can use up to sixteen supervised 32-character LCD keypads; network communications;

zone and output expansion modules; and initiating and indicating circuit modules. You can also connect auxiliary devices

to the panel’s output relays to expand the basic system control capability. Combined current requirements of additional

modules may require an auxiliary power supply. Refer to the XR100 Series Power Requirements section in this guide when

calculating power requirements.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 35 36

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products Canadian XR100 Instalační příručka Strana 8

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products Canadian XR100