Digital Monitoring Products XTL Series Instalační příručka stáhnout pdf (Strana 33)

Digital Monitoring Products XTL/XTLC Programming Guide

ZONE INFORMATION

This option displays when programming an 1114 zone expander which provides four input

contacts. Press any top row key to select the contact. Default is Contact 1.

Select the contact number to program. The same transmitter serial number is used for

all four contacts. When using the contacts, you must use consecutive zone numbers.

For example, use serial number 08345678 to program Contact 1 for Zone 21, Contact 2

for Zone 22, Contact 3 for zone 23, and Contact 4 for zone 24.

A tamper on the 1114 is transmitted as the zone number assigned to Contact 1.

This message displays when the Contact is already programmed for another zone. The

programmed zone number displays.

The Normally Open option only displays when EXT is selected as the Contact type. For

external devices connected to the 1101 terminal block, select NO to use normally closed

(N/C) contacts. Select YES to use normally open (N/O) contacts. Default is NO.

13.10.1 Supervision Time

Press any top row key to select the supervision time required for the wireless zone. Press

COMMAND to accept the default time. Default is 240 minutes.

Select the required number of minutes. The transmitter must check in at least

once during this time or a missing condition is indicated for that zone. 1100 Series

transmitters automatically checkin based on the supervision time selected for the

wireless zone, no additional programming is needed. If two zones share the same

transmitter, the last programmed supervision time is stored as the supervision time for

both zones. Zero (0) indicates an unsupervised transmitter.

The 3 minute supervision time is only available for zone types of Fire (FI), Fire Verify

(FV), and Supervisory (SV).

Note: When the panel is reset or a receiver is installed or powered down and powered

up, the supervision timer restarts for all wireless zones.

13.10.2 LED Operation

This only displays when programming a panic or pendant transmitter. Select YES to turn

a panic or pendant LED on during normal operation. Select NO to turn the LED off during

normal operation. The LED always operates on all transmitters when the transmitter

case is open and the tamper is faulted. Default is YES.

13.10.3 Disarm/Disable

Select YES to disable the zone tripped message from an 1103 Universal Transmitter

(Version 107 or higher software) or 1126/1127 PIRs during the disarmed period. When

disarmed, the transmitter or PIR only sends supervision, tamper, and low battery

messages to extend transmitter battery life. For 1103 Transmitters, a zone tripped

message is sent if the zone remains tripped for 20 seconds. Select NO to always send

zone tripped messages in addition to supervision, tamper, and low battery.

Default is YES.

13.10.4 Wireless PIR Pulse Count

Select the number of infrared pulse counts (2 or 4) the PIR will use before sending a

short message. The rst infrared pulse starts a timer and count. If no additional infrared

pulses occur in 25 seconds, the timer and count are reset. Default is 4.

13.10.5 Wireless PIR Sensitivity

Select the sensitivity setting for the PIR. Selecting LOW sets the PIR to operate at

75% sensitivity for installations in harsh environments. Selecting HIGH sets the PIR to

maximum sensitivity. Default is LOW.

13.10.6 Next Zone

Select YES to return to the ZONE NO: - option to program a new zone. Select NO to

display the Alarm Action option.

CONTACT: x

1 2 3 4

ALREADY USED Zxx

NORM OPEN NO YES

SUPRVSN TIME: XX

0 3 60 240

LED OPER NO YES

DISARM DISABLE

YES

WIRELESS PIR

PULSE COUNT:

WIRELESS PIR

SENSITIVITY: LOW

NEXT ZN NO YES

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 48 49

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products XTL Series Instalační příručka Strana 33

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products XTL Series