Digital Monitoring Products XTL Series Instalační příručka stáhnout pdf (Strana 37)

Digital Monitoring Products XTL/XTLC Programming Guide

ZONE INFORMATION

13.13.3 Output Action

Entering an Output Number displays this option that allows you to assign an output

action. A description of the available output actions is given below:

STEADY - The output is turned on and remains on until the area is disarmed, an output

cutoff time expires, or the output is reset from the keypad User Menu.

PULSE - The output alternates one second on and one second off until the area is

disarmed, an output cutoff time expires, or the output is reset from the keypad User

Menu.

MOMENTARY - The output is turned on only once for one second.

FOLLOW - The output is turned on and remains on while the zone is in an off normal, or

bad condition. When the zone restores, the output is turned off.

After you have selected the Message To Transmit, the display prompts you for the same

three selections for Disarmed Short, Armed Open, and Armed Short conditions. If the

zone is a 24-hour type, only the Armed Open and Armed Short conditions are displayed.

When you have programmed all of the zone conditions, the Swinger Bypass selection is

then dis played.

13.14 Swinger Bypass

Selecting YES allows the zone to be swinger bypassed by the panel according to the

programming in Swinger Bypass Trips and Reset Swinger Bypass. The Bypassed zone

displays in the keypad Status List. Selecting NO disables swinger bypassing for this zone.

How it works

If within one hour, a zone trips the total number of times as specied in Swinger Bypass

Trips, the panel bypasses it until the following conditions occur; the area in which

the zone is assigned is disarmed, the zone is manually reset through the Bypass Zones

keypad User Menu function, the zone remains normal for one hour and the Reset Swinger

Bypass is YES.

If the zone trips fewer than the specied times within one hour of the rst trip, the

bypass trip counter returns to 0 (zero) and the process must be repeated.

A report of the swinger bypass is sent to the receiver if Bypass Reports is YES.

13.15 Prewarn Address

Option is only shown for an Exit zone.

At the start of the entry delay, all keypad addresses dis play ENTER CODE:-. If you want

the prewarn to sound at all addresses, leave the default as shown.

To delete an address, press the matching number on the keypad. To disable prewarning

at all keypads, press a top row key to clear the addresses shown. Press the COM MAND

key when the address selection is com plete.

Note: The prewarn tone stops at the keypad when the rst digit of a user code is

entered. If, within ve seconds, a valid user code is not entered or an invalid user code

is entered, the prewarn tone begins sounding again. Fifteen seconds must elapse before

entering a digit silences the prewarn tone again.

13.16 Entry Delay

Option is only shown for an Exit zone. Select the entry delay timer for this zone. Entry

delay timers 1 and 2 are programmed in Entry Delay in the System Options menu.

13.17 Cross Zone

Select YES to enable cross-zoning for this zone. Cross-zoning requires this zone to trip

twice, or this zone and another cross-zoned zone to trip, within a programmed time

before an alarm report is sent to the receiver.

Note: To operate correctly, all cross-zone zones need to be programmed as the same

zone type.

When a cross-zoned zone trips, the Output action assigned to the zone activates. See the

Bell Action section. The cross-zone time specied in System Options begins to count down.

See the Cross-Zone Time section. If another cross-zoned zone in the system faults, or if the

rst zone restores and faults again before the cross-zone time expires, the bell turns on

and the panel sends an alarm report.

ACTION:

NO YES

STD PLS MOM FOLW

SWGR BYP NO YES

PREWARN: 12345

ENTRY DELAY: 1

CRS ZONE NO YES

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 48 49

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products XTL Series Instalační příručka Strana 37

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products XTL Series