Digital Monitoring Products XT50 Instalační příručka stáhnout pdf (Strana 17)

Digital Monitoring Products XT Series Programming Guide

COMMUNICATION

3.28 Opening/Closing and User Reports

YES enables Opening/Closing, Door Access, Schedule and Code Changes, Bypass, and

Sensor Reset reports by user to be sent to this receiver. Default is NO.

3.29 Test Report

YES enables the Recall Test report to be sent to this receiver. Default is NO.

3.30 First Telephone Number

Enter the rst number the panel dials to send reports to this receiver. A phone number

may contain two lines of 16 characters to equal 32 characters. You can program a

three-second pause in the dial ing se quence by en tering P. Program a dial tone detect by

entering D. These characters are counted as part of the 32 characters.

Call Waiting: You can place the “* 7 0 P” (Star, Seven, Zero, Pause) in the telephone

number rst position to cancel Call Waiting. For example, program NET with second line

DD and phone number *70P555-1212, and you have NET with Call Waiting cancelled on

the second line.

Caution: A call waiting cancel programmed on a non-call waiting telephone line

would prevent communication to the central station.

3.31 Second Telephone Number

The panel dials the second number after two successive attempts failed using the rst

number. If the panel cannot reach this receiver after two attempts using the second

number, it returns to the rst number and makes two additional attempts. A total of ten

dialing attempts are made using the rst and second phone num bers. If a second phone

number is not entered, the rst phone number is used for all dialing attempts. Each

number can be up two lines of 16 characters to equal 32 characters in length, in cluding

any P, D, or *70P char acters entered for pause, dial tone detect, or call waiting cancel

option.

3.32 First IP Address

Enter the rst (primary) IP address where the panel sends network or cell messages.

The IP address must be unique and cannot be duplicated on the network. Enter all

12 digits and leave out the periods. For example, enter IP address 192.168.0.250 as

192168000250. The periods display automatically.

For NET: The rst and second IP addresses are alternately used for 8 second intervals

until successful communication or 1 minute elapses.

For Cell: The message is sent using First GPRS APN and the First IP Address. If no

acknowledgment is received, First GPRS APN and the Second IP address are used,

followed, if needed, by Second GPRS APN and rst and second IP addresses, respectively.

3.33 First IP Port

Enter the rst IP port number to be used in conjunction with the First IP Address.

The IP port identies the port used to communicate messages to and from the panel.

The default IP Port setting is 2001.

3.34 Second IP Address

Enter the second IP address where the panel sends network messages. The IP Address

must be unique and cannot be duplicated on the network. Enter all 12 digits and leave

out the periods. For example, enter IP address 192.168.0.250 as 192168000250. The

periods display automatically.

3.35 Second IP Port

Enter the second IP port number to be used in conjunction with the Second IP Address.

The IP port identies the port used to communicate messages to and from the panel.

The default IP Port setting is 2001.

O/C USER NO YES

TEST RPT NO YES

FIRST PHONE NO.

SECOND PHONE NO.

FIRST IP ADDR

000.000.000.000

FIRST IP PORT

2001

SECOND IP ADDR

000.000.000.000

SECOND IP PORT

2001

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 54 55

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products XT50 Instalační příručka Strana 17

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products XT50