Digital Monitoring Products Canadian XR100 Manuál s instrukcemi stáhnout pdf (Strana 35)

XR100 Series Programming Guide Digital Monitoring Products

SyStem OptiOnS

9.5

ENTRY DLY 2: 60

ENTRY DLY 3: 90

ENTRY DLY 1: 30

ENTRY DLY 4: 120

Entry Delay 1

EntertheEntryDelaytimeforallExittypezonesprogrammedtouseEntryDelay

1.WhenanarmedExittypezoneisfaulted,thekeypadprewarntonebegins

sounding.AllkeypadsprogrammedtoprewarnforthatzonedisplayENTERCODE:-

andthenameofthezonecausingtheentrydelay.Whentherstdigitofacodeis

entered, the prewarn tone stops at that keypad. If an invalid code is entered, the

prewarn tone begins sounding again. The area must be disarmed before the delay

expires or an alarm report is sent to the receiver and an alarm sounds. All zones in

thatareaaredelayedalongwiththeExitzone.EntryDelaytimescanbefrom30to

250seconds.Repeattheaboveforeachentrydelaybeingusedinthesystem.

Note:SpecicExitErroroperationisbasedontheEntryDelayused(1-4)withan

EXtypezone.SeeExitDelay.

Note: For UL Installations, the combined Transmit Delay (Abort Window) and

Entry Delay must not exceed one (1) minute.

9.6

CRS ZONE TM: 4

Cross Zone Time

Enterthetimeallowedbetweenzonefaults.Whenzonesarecrosszoned,the

same zone or a second cross zoned zone must fault within this time in order for

an alarm report for both zones to be sent to the receiver. If the cross zone time

expireswithoutthesecondzonefaulting,onlyazonefaultfromtherstzoneis

reported.Cross-zonetimecanbefrom4to250seconds.Entering0(zero)disables

this function. Default is 4. See the Appendix.

9.7

RETARD DELAY: 10

Zone Retard Delay

EntertheretardtimeassignedtoFire,Supervisory,Auxiliary1,Auxiliary2,

Arming, and Panic type zones. The retard delay only functions when the zone is

shorted. The zone must remain shorted for the entire length of the Retard Delay

beforebeingrecognizedbythepanel.TheZoneRetardDelaycanbefrom1to250

seconds.Enteringa0(zero)disablesthisfunction.

9.8

PWR FAIL HRS: 1

Power Fail Delay

This option tracks the duration of an AC power failure. When the AC power is off

for the length of the programmed delay time, an AC power failure report is sent to

thereceiver.Thedelaytimecanbefrom1to15hours.Enteringa0(zero)sends

thepowerfailurereportaftera15-seconddelay.Thedefaultsettingis1.

Note: For UL burglary installations Power Fail Delay shall be programmed to 0

(zero).

Note: For UL re installations, Power Fail Delay shall be programmed as

required by the service of the panel. For Central Station service: 6-12, for

Remote Station service: 12-15.

9.9

SWGRBYPS TRIPS: 2

Swinger Bypass Trips

Enterthenumberoftimes(1-6)azonecangointoanalarmortroublecondition

within one hour be fore being auto matically bypassed. You can select one or two

trips. Bypassed zones are auto matically reset when the area they are assigned to

isdisarmed.All24-hourzonesareresetwhenanyareaofthesystemisdisarmed.

AprogrammingStopoperationrestoresabypassedzone.Entering0(zero)disables

thisfunction.Defaultis2.

How it works

Thepanelhourtimerstartsat59minutespastthehour.Ifthehourtimerexpires

beforethetripcounterisexceeded,thetripcounterreturnsto0(zero).Ifthetrip

counter is exceeded before the hour expires, the zone is auto matically bypassed by

thepanel.ABypassReportissenttothereceiverifBypassReportsisYES.

Note: Not investigated by UL.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 77 78

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products Canadian XR100 Manuál s instrukcemi Strana 35

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products Canadian XR100