Digital Monitoring Products Canadian XR100 Manuál s instrukcemi stáhnout pdf (Strana 52)

Digital Monitoring Products XR100 Series Programming Guide

AreA InformAtIon

17.12

AUTO ARM NO YES

Automatic Arming

SelectYEStoallowthisareatoarmautomaticallyaccordingtopermanent,

temporary, or extended schedules. If no schedules are programmed, the area auto

arms every hour.

IfclosingcheckisselectedasYES,theautomaticarmingfunctiondoesnottake

place until the expiration of a ten minute Closing Check delay. See Closing Check. If

the area has been disarmed outside of any permanent or temporary schedule, the

closing check sequence occurs one hour after the area is disarmed.

At arming, bad zones are handled according to the option selected in section Bad

Zones.Ifaclosingreportissent,theusernumberisindicatedasSCHontheSCS-1R

Receiver. NO disables automatic arming for this area.

Note: For ANSI/SIA CP-01 UL installations, Automatic Arming cannot be used for

arming.

17.13

BAD ZONES: BYP

Bad Zones

At the time of automatic arming, some zones in the area may not be in a normal

condition. This option allows you to program the panel response to these bad

zones.ThisoptiondoesnotdisplayifAUTOARMisNO.

BYP FORC REF

BYP - All bad zones are bypassed. A report of the bypass is sent to the receiver if

BypassReportsisYES.ThereportindicatesSCHastheusernumber.

FORC - Allbadzonesareforcearmed.Zonesforcearmedinabadconditionare

capable of restoring and reporting an alarm if tripped. A forced zone report is

transmittedifBypassReportsisYES.ThereportindicatesSCHastheusernumber.

REF - The automatic arming is refused and no arming takes place. A No Closing

report is sent to the receiver regardless of the Closing Check selection.

17.14

AUTO DIS NO YES

Automatic Disarming

NOdisablesautomaticdisarmingbyscheduleforthisarea.WhenYESisselected,

the area automatically disarms according to permanent or temporary schedules. If

an opening report is sent to the receiver, the user number is indicated as SCH.

Note: For ANSI/SIA CP-01 UL installations, Automatic Disarming cannot be used

for disarming.

17.15

ARMED OUTPUT: 0

Armed Output Number

Entertheoutputtoturnonwhenthisareaisarmed.Ifanexitdelayisusedforthis

area, the Armed Output turns on at the start of the exit delay. The output is turned

offwhenthisareaisdisarmed.TheoutputcannotbeturnedonfromtheUserMenu

OutputsOn/Offoption.

17.16

LATE OUTPUT: 0

Late Output Number

Entertheoutputtoturnonwhenthisareaisnotarmedbyitsscheduledtime

andAreaLateorClosingTimedisplaysatakeypadandthekeypadbuzzerison.

The output is turned off when the keypad buzzer is silenced by pressing any key.

Defaultis0(zero).

17.17

LATE/ARM DLY: 60

Late Arm Delay

Enter4to250minutestodelaybeforeautomaticre-armingoccursafterthearea

becomesdisarmedoutsideofschedules.SeeClosingCheck.Defaultis60minutes.

Note:TheLateArmDelaycanbesupersededbytheReArmDelaysettingofthe

UserProleassignedtotheuserwhodisarmedthearea.RefertotheReArmDelay

sectionintheXR100SeriesUser’sGuide(LT-0683).

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 77 78

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products Canadian XR100 Manuál s instrukcemi Strana 52

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products Canadian XR100