Digital Monitoring Products Canadian XR100 Manuál s instrukcemi stáhnout pdf (Strana 69)

XR100 Series Programming Guide Digital Monitoring Products

Appendix

21.4 Using the Walk Test

The XR100 Series panel provides a walk test feature that allows a single technician to test the protection

devicesconnectedtozonesonthesystem.ConducttheWalkTestwithin30minutesofresettingthepanel.

TheWalkTestautomaticallyendsifnozonesaretrippedfor20minutes.TESTINPROGRESSdisplaysatall

keypadsprogrammedwiththesameAreaDisplayfeatures.Whenveminutesremain,TESTENDWARNING

displays. The Walk Test only tests zones assigned to the areas programmed into the keypad in Area Display.

IfanyareasarearmedtheWalkTestdoesnotstartandSYSTEMARMEDdisplays.

Note:IfthePanicSupervisionoptionisenabledinSYSTEMOPTIONS,thepanicbuttononanyprogrammed

keyfobcanbetestedduringtheWalkTest.Whenthepanicbuttonispressedavericationmessageissent

by the receiver.

WALK TEST

Walk Test

To conduct the Walk Test, reset the control panel by momentarily placing a

jumperonJ16.Fromthekeypad,enterthecode8144andpressCOMMAND.The

keypaddisplaysWALKTESTforfourseconds.Ifthesystemismonitoredandthe

communicationtypeisDDorNET,thesystemsendsaSystemTestBeginreportto

the central station. After four seconds, the keypad displays the zone type choices

for testing.

*BG *FI *PN *SV

Zone Types

Select the zone type you want to test. An asterisk next to the zone type indicates the

zone type chosen for testing. Press the Select key again to deselect the zone type.

When you have selected all the zone types you want for testing, press the COMMAND

key to display the next Walk Test option. Pressing the Back Arrow key exits the Walk

Test.

BG(Burglaryzones)-SelectBGtotestburglaryzones.IncludesallNT,DY,EX,A1,

andA2zones.

FI(Firezones)-SelectFItotestrezones.IncludesallFIandFVzones.

PN(Paniczones)-SelectPNtotestpaniczones.IncludesallPNandEMzones.

You do NOT havetoholdthezonesfor2secondsinnormalmode.Youareonly

required to hold the panic during the Walk Test because the zone takes additional

time to report when the system is in test mode.

SV(Supervisoryzones)-SelectSVtotestsupervisoryzones.IncludesallSVzones.

Note: During the Walk Test, trip each zone device or button on the system for 1 to

2seconds.

WLS PIR

WLS(WirelessCheck-inTest)-SelectWLStoautomaticallytestwirelesstransmitter

communications. Includes all wireless devices except key fobs and transmitters

programmedforasupervisiontimeof0(zero).

PIR(WirelessPIRWalkTest)-ThePIRWalkTestallowstheinstallertoverifythe

1126operation.Whenenabled,the1126LEDasheseachtimemotionisdetected

forupto30minutes.Thisisalocaltestonlyandnomessagesaresenttothe

Central Station.

BELL NO YES

Bell Action

This option selects the bell output action when a zone under test faults. This option

allowsthepanelbell,and/orburglarybell,and/orrebelltoturnONandthen

OFFeachtimeazoneistripped(openedorshorted).

NO - Select NO for no bell output action during Walk Test.

YES - SelectYEStoturnonanybelloutputfor2secondsduringWalkTest.

PULS -SelectPULStoturnonanybelloutputfor1/4secondduringWalkTest.Any

LX-Busdeviceoutputturnsonfor1.6secondsduetothepollingcycle.

TRIPS: XXX END

Trip Counter For Walk Test

Once in the Walk Test, walk around and trip each protective device. Continue

tripping devices until the entire system is tested.

1 2 ... 64 65 66 67 68 69 70 71 72 73 74 ... 77 78

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products Canadian XR100 Manuál s instrukcemi Strana 69

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products Canadian XR100