Digital Monitoring Products Canadian XR100 Manuál s instrukcemi stáhnout pdf (Strana 48)

Digital Monitoring Products XR100 Series Programming Guide

PC Log RePoRts

PC Log Reports

16.1

PC LOG REPORTS

PC Log Reports

ThissectionallowsyoutoprogramthetypesofPCLogReportsthepanelsends

through the J1 network connector directly on the XR100N panel. The reports

include information such as the type of activity, time and date of the activity, and

user name and number. These data reports can be accessed from a PC using the

Advanced Reporting Module.

Note:ThenetworkconnectionthatsendsPCLogReportsisnotmonitoredfor

networktrouble.ThePCLogReportsoptionshouldNOTreplacetheprimary

communication method or act as a backup communication method.

If there is trouble with the network connection, the panel continues to attempt to

sendthePCLogReportsuntiltheconnectionisreestablished.Thepanelthensends

the reports. A Network Trouble message is NOT sent if the connection is lost since

thisreporttoolisnotdesignedtobemonitoredbyareceiver.ThePCLogReports

have the lowest priority of panel reports sent.

Note: To enable remote programming direct connection operation with the panel

throughtheLXheader(J22),donotenteraPCLogAddressandsetallreport

optionstoNO.RefertotheXR100SeriesInstallationGuide(LT-0899)forJ22

connection and operation.

16.2

COMM TYPE: NONE

Communication Type

NONE NET

SelecttheCommunicationTypetosendthePCLogReports.DefaultisNONE.

16.3

NET IP ADDRESS

Net IP Address

ThisoptiondisplayswhentheCommunicationTypeforPCLogReportsisNET.Enter

theIPaddresscontainingupto16characters.TheNetIPAddressmustbeunique

andcannotbeduplicatedonthenetwork.Enterall12digitsandleaveoutthe

periods.Forexample,enterIPaddress192.168.0.250as192168000250.Theperiods

display automatically.

16.4

NET PORT 2001

Net Port

ThisoptiondisplayswhenCommunicationTypeforPCLogReportsisNet.Enterthe

Portnumber.Validnumbersarefrom0to65535.Defaultis2001.

16.5

ARM/DIS NO YES

Arm and Disarm Reports

Sendsarming,disarmingandLatetoCloseevents.Includestheareanumber,name

and action, the user number and name, and the time and date.

16.6

ZONE NO YES

Zone Reports

Sends changes in the status of active zones. Includes the zone number, name, type,

theaction(alarm,trouble,bypass,etc.),usernumber(ifapplicable),andarea

name.ForaWalkTest,VerifyandFailmessagesaresentforeachzone.

16.7

USR CMDS NO YES

User Command Reports

Sends user code changes, schedule changes, and door access denied events.

16.8

DOOR ACS NO YES

Door Access Reports

Sends door access activity: door number, user number and name, and time and

date.

16.9

SUPV MSG NO YES

Supervisory Reports

Sends system monitor reports, such as AC and battery, and system event reports.

Supervisory Reports also sends the following reports:

•Abort •ExitError •Ambush

•SystemRecentlyArmed •AlarmBellSilenced •UnauthorizedEntry

•*LatetoClose

*OnlysentasaSupervisoryReportifArea Schedules is not enabled, Closing

Checkisenabled,andanopening/closingschedulehasbeenprogrammed.

Note: TosendthesereportstothePCLog,youmustenableSUPVMSG.

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 77 78

Komentáře k této Příručce

Žádné komentáře

Digital Monitoring Products Canadian XR100 Manuál s instrukcemi Strana 48

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digital Monitoring Products Canadian XR100