Digital Monitoring Products Canadian XR100 Manuál s instrukcemi Strana 9

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 78
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 8
XR100 Series Programming Guide Digital Monitoring Products
1
IntroductIon
Introduction
1.1 Before you Begin
This guide provides programming information for the DMP XR100 and XR100N Panel. After this Introduction,
the remaining sections describe the functions of each programming menu item along with the available
options. Before starting to program, we recommend that you read through the contents of this guide.
The information contained here allows you to quickly learn the programming options and operational
capabilities of the XR100 and XR100N panels.
In addition to this guide, you should also read and be familiar with the following XR100 Series documents:
• XR100SeriesInstallationGuide(LT-0899)
• XR100SeriesProgrammingSheet(LT-0897)
• XR500/XR100User’sGuide(LT-0683)
Internal Programmer
Thepanelcontainsallofitsprogramminginformationinanon-boardprocessoranddoesnotrequirean
externalprogrammer.Youcanperformallprogrammingtasksthrougha32-characterDMPalphanumeric
keypad set to address one.
Programming Information Sheet
Included with each panel are the Programming Information Sheets. These list the various programming
options and available options for programming the panel. Before starting to program, we recommend you
completelyllouteachsheetwiththeprogrammingoptionsyouintendtoenterintothepanel.
Having completed programming sheets available before entering data helps prevent errors and can shorten
the time you spend programming. Completed sheets also provide you with an accurate panel program
recordyoucankeeponleforfuturesystemserviceorexpansion.TheremainderofthisIntroduction
provides instructions for starting and ending a programming session using the alphanumeric keypad.
1.2 Getting Started
Ground Yourself Before Handling the Panel! Touch any grounded metal, such as the enclosure, before
touching the panel to discharge static.
Remove All Power From the Panel! Remove all AC and Battery power from the panel before installing or
connecting any modules, cards, or wires to the panel.
Before starting to program the XR100 Series panel, make sure the panel is properly grounded and AC
and battery power is applied to the appropriate panel terminals. All wiring connections and grounding
instructionsaredetailedintheXR100SeriesInstallationGuide(LT-0899).
Program from any Keypad Address or Wireless Keypad
YoucanprogramtheXR100panelfromany32-characterwirelesskeypadorhardwiredkeypadconnected
tothepanel’skeypaddatabus.SeetheXR100InstallationGuideforkeypadaddressingandinstallation
information for hardwired keypads.
Wireless Keypads can be used for panel programming after being programmed in the panel manually or by
using the Wireless Keypad Association operation.
Toenableassociationoperationinthekeypad,accesstheInstallerOptionsMenu(3577(INST))and
selectRFSurvey.ThekeypadlogoLEDsturnonReduntilassociationissuccessful.
ToenableassociationoperationintheXR100panel,resetthepanel3timeswithin12seconds.Allow
thepanel’skeypadbusTransmit/ReceiveLEDstoturnbackonbetweeneachreset.
For60secondsthepanellistensforwirelesskeypadsthatareintheInstallerOptionsMenuandhave
notbeenprogrammed,orassociatedintoanotherpanel.Thosekeypadsareassignedtotherstopen
device position automatically based upon the order in which they are detected. The keypad logo
turnsGreentoindicateithasbeenassociated
withthepanel.Seethe9000SeriesWireless
KeypadInstallationGuide(LT-1107)foradditional
information.
Accessing the Programmer
1. Momentarily place the Reset jumper over both of
theJ16pinstoresetthepanel.
2. Enterthecode6653(PROG)andpressCOMMAND.
3. The keypad displays: PROGRAMMER.
To enable Wireless Keypad
Association operation:
Reset panel 3 times within
12 seconds.
To access the programmer:
Momentarily place the
Reset jumper over both of
the J16 pins to reset the
panel.
J16
Reset
AC
12345678 10 11 12 13 14 15 16 17 18 19
92
02122232425262728
+B BELL GND SMK GNDRED YEL GRN BLKZ1Z2Z3Z4Z5Z6Z7Z8 Z9+ Z9– Z10+ Z10–AC –B GND GND GNDGND
K6 K7
Output 1Output 2
J3
Phone Line
J10
J22
LX-Bus
Battery
Start
Power
LED
J8
PROG
J4
Tamper
Out1 Out2
Outputs 3-6
J11
3
4
5
6
J2
J1
Ethernet
OVC
Link LED
Activity LED
J23
R
L
X
Figure 1: XR100 Series Panel Showing Reset
Zobrazit stránku 8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 77 78

Komentáře k této Příručce

Žádné komentáře